2005 15' ALERT (Sport) Whaler - leaking thru hull plug
|
nvrenuf |
Posted on 08/30/21 - 10:18 AM
|
Member
Posts: 5
Comments:
0
Joined: 08/30/21
|
I am having issues attaching a picture of the additional piece that accepts the rubber plug
Edited by nvrenuf on 08/30/21 - 10:19 AM |
|
|
|
nvrenuf |
Posted on 08/30/21 - 10:24 AM
|
Member
Posts: 5
Comments:
0
Joined: 08/30/21
|
Hello Everyone - I have a 2005 15' ALERT, same as a 15 Sport but with plastic seating not wood.
Issue I have is a leak in the rear hull plug, the one lowest in the boat.
It is NOT leaking around the plug. It is leaking by the push in piece that the plug goes into.
nvrenuf attached the following image:
[40.61Kb]
|
|
|
|
nvrenuf |
Posted on 08/30/21 - 10:27 AM
|
Member
Posts: 5
Comments:
0
Joined: 08/30/21
|
Here is a picture of the outside plug
Where can I buy these / how do I find the right part number for a 2005 CPD / Boston Whaler ALERT - SPORT 15.
thanks everyone!
scott
|
|
|
|
nvrenuf |
Posted on 08/30/21 - 10:27 AM
|
Member
Posts: 5
Comments:
0
Joined: 08/30/21
|
Hopefully the rear picture attaches this time.
My rear plug seems to be coming out of the boat / not flush.
I am having issues attaching photos. The file is really small so that should not be the issue.
Edited by nvrenuf on 08/30/21 - 10:28 AM |
|
|
|
Phil T |
Posted on 08/30/21 - 11:44 AM
|
Administrator
Personal Page
Personal Album
Project Albums
Posts: 6991
Comments:
6
Joined: 03/26/05
|
Are you turning the T part to tighten/loosen?
Email me the full size photos. Click on my name to get my email address.
1992 Outrage 17 I
2019 E-TEC 90, Viper 17 2+
2018 Load Rite Elite 18280096VT |
|
|
|
Joe Kriz |
Posted on 08/30/21 - 12:35 PM
|
Site Owner
Personal Page
Personal Album
Photo Albums
Project Albums
Posts: 11434
Comments:
452
Joined: 03/18/05
|
nvrenuf wrote:
I am having issues attaching a picture of the additional piece that accepts the rubber plug
Hi nvrenuf:
The name of the photos cannot contain any characters or spaces and of course the filesize needs to be under 200kb
The one you uploaded was fine and was named inside.jpg which is why it worked.
|
|
|
|
nvrenuf |
Posted on 09/03/21 - 9:48 AM
|
Member
Posts: 5
Comments:
0
Joined: 08/30/21
|
I have removed the factory looking pieces on the inside and outside of the boat.
My hole ID is 1.55" and is 14" long
I believe this is the factory size hole
Local boat repair only has brass forming crimp tool for a 1" hole.
Remember, this boat is an odd duck - ALERT 15
It is not a SPORT 15
thanks for all your support
nvrenuf attached the following image:
[46.98Kb]
|
|
|
|
Phil T |
Posted on 09/03/21 - 10:24 AM
|
Administrator
Personal Page
Personal Album
Project Albums
Posts: 6991
Comments:
6
Joined: 03/26/05
|
Good to talk Scott.
Think you should be all sorted.
1992 Outrage 17 I
2019 E-TEC 90, Viper 17 2+
2018 Load Rite Elite 18280096VT |
|
|