1. Use the full 4 digit year for everything you are asking your question about. Example: 1962, 1988, 2000, 2011
2. Include the correct name of your Whaler model. Example: Montauk 17, Montauk 170, Outrage 26, Outrage 260
3. Include the length when necessary. Example: 16, 17, 18, 20, 22
4. Do not post your email address anywhere on this site as it is already in your user profile.

Has anyone put a Hydraulic Jackplate on Sport
Cobra1169	#1  Posted on 06/29/15 - 7:46 PM
Member Posts: 4 Comments: 0 Joined: 06/18/15	I'm looking to see if anyone has put a hydraulic jack plate on a Whaler 13' or 15' sport. If so was it worth the investment and what were the benefits. I'm considering one for repowering of boats with 2015 4 Stroke 40HP on 13' and/or 70hp on the 15'. with a Atlas Micro Jacker. I'll be running the boat on the Texas Gulf Coast where the is very skinny water. Thank you.
wlagarde	#2  Posted on 06/29/15 - 8:21 PM
Member Personal Page Project Albums Posts: 442 Comments: 2 Joined: 07/21/13	I added that exact plate to my Sport 15 this year. Outstanding results. It added 1-2 mph to my top speed and allows me to go into very skinny water (just got back from a week at the NC coast and it was really handy running the shallows of the intracoastal waterway). Another benefit was the result of moving the engine almost completely out of the boat. To compensate for moving the CG aft I moved the battery from the stern to under the rear thwart seat. There are some pictures of my setup on my personal page. 1976 Sport 15 w/ 2005 50hp Nissan 2 stroke
Cobra1169	#3  Posted on 06/29/15 - 8:49 PM
Member Posts: 4 Comments: 0 Joined: 06/18/15	Excellent! Thanks for the feedback, it is very much appreciated!
wlagarde	#4  Posted on 06/29/15 - 9:01 PM
Member Personal Page Project Albums Posts: 442 Comments: 2 Joined: 07/21/13	Also, the micro jacker is a great plate. Fast motion, very light, hydraulics contained within the plate (so no extra space taken up in a boat with already limited space), and the quality of the machining of the aluminum is excellent. I can also now trailer the boat without tilting the engine. 1976 Sport 15 w/ 2005 50hp Nissan 2 stroke
Phil T	#5  Posted on 06/30/15 - 7:54 AM
Administrator Personal Page Personal Album Project Albums Posts: 6985 Comments: 6 Joined: 03/26/05	Watch out, the OP is installing a new 4 stroke motor. The added weight of the 4 stroke and the jackplate may be too much. Figure out the added weight and then do a mock-up on the boat to determine if it will work. Adding a fixed jackplate will only result in reducing your draft by an inch or two but will add undesirable weight and cost.
wlagarde	#6  Posted on 06/30/15 - 9:49 AM
Member Personal Page Project Albums Posts: 442 Comments: 2 Joined: 07/21/13	Agree with Phil look at the total weight. My total with the JP is about 190#. The microjacker is one of the lightest hydraulic JPs on the market at 23#. 1976 Sport 15 w/ 2005 50hp Nissan 2 stroke
dgoodhue	#7  Posted on 06/30/15 - 5:31 PM
Member Posts: 278 Comments: 0 Joined: 10/04/05	I have a 260# 2 stroke motor on my classic 15' SS with a mechanical jackplate. The boat doesn't sit that low with the jack plate (the water line is at the rear splash well). The 70 Mercury of the era were 275#. I think if you used a new Yamaha 70hp (which weights about 260#) with a light jack plate that you would be fine. Any other current 70 or 75 motor is going to be too heavy. I am pretty sure the 13' and a new four stroke 40 is going to be too heavy as well. IMO the jack plate is worth 2mph. I have my motor raises another 2.5" higher than I could have run it with the motor on the transom. It planes off easily (much better in fact than the too low of position that it was mounted when I purchased the motor). If you into speed (or higher cruise speeds). The 15' with 70 is almost 10 mph faster than the 13' 40hp, plus it has a much higher cruising speed. The 15' ride better then only down side besides cost is the 13' has more lateral stability and a slower planning speed. Edited by dgoodhue on 06/30/15 - 5:32 PM Dave
gchuba	#8  Posted on 06/30/15 - 5:40 PM
Member Posts: 1675 Comments: 0 Joined: 03/31/13	Bob's Machine Hydraulic Jack Plate gives you the option of self contained or hydraulic motor mounted in a protected area at another part of the boat. Would save some weight on the transom. Garris Edited by gchuba on 06/30/15 - 6:26 PM